Equipment
Power Tool Inspection Checklist: Pre-Use Checks
- Frequency
- Before each use
- Completed by
- Tool user
- Approved by
- Supervisor
- The checklist
- 30 checks · 6 sections
A power tool inspection checklist is the short check a user makes before working with a hand-held power tool: casing and handles, guards, the blade, disc or wheel, the cable and plug, the battery pack or air hose, and the switch. This one covers mains (corded), battery and pneumatic tools. A tool that fails a critical check is taken out of use and tagged until it has been repaired.
In the United States, OSHA 29 CFR 1910.334(a)(2) requires portable cord- and plug-connected equipment and extension cords to be visually inspected before use on any shift, and defective items to be removed from service; 1910.243, 1926.300 and 1926.302 set the rules for guards, switches and pneumatic tools. In Türkiye, Annex III of the Work Equipment Regulation requires operators to check work equipment before each start of work. In Great Britain, HSE's HSG107 recommends a user check when equipment is taken into use and during use, and notes that the law does not fix what must be done or how often.
This user check does not replace formal visual inspection and testing (PAT) by a competent person, or the maintenance in the manufacturer's manual. For the sockets, leads and panels the tools are plugged into, see our electrical safety inspection checklist; for vibrating tools, see the hand-arm vibration risk assessment.
How to use this checklist
- Complete the checklist before the first use of the shift, and again whenever you take over a different tool.
- Do the visual checks with the tool switched off and disconnected: plug out, battery removed or air hose uncoupled.
- Mark the sections that do not apply to your tool N/A: a battery drill has no cable or air hose to check.
- Reconnect the tool with its switch off, then do the short function test away from other people.
- If a critical check fails, do not use the tool: tag it "Do not use", hand it to your supervisor and take another one.
- Add any checks that the manufacturer's manual lists for the model, and keep the completed form with the tool register.
The checklist: Power Tool Inspection Checklist: Pre-Use Checks
Inspection details
Tool, guards and accessory (disconnected)
- 1.
The tool is the right type for the job and for the place it will be used
Check the manual for limits such as wet or damp locations.
PassFailN/A - 2.
Casing and handles are free of cracks and breaks, with no loose or missing screws or partsCritical
PassFailN/A - 3.
The tool is dry and not heavily contaminated with dust, oil or other material
Ref.: [8]
PassFailN/A - 4.
There are no burn marks or discolouration on the tool, cable or plugCritical
These are signs of overheating.
Ref.: [8]
PassFailN/A - 5.
Every guard the tool is designed to have is fitted, undamaged and secured in the correct positionCritical
On a grinder the guard sits between you and the wheel.
PassFailN/A - 6.
On a circular saw, the lower guard moves freely and returns to cover the blade by itselfCritical
Mark N/A for other tools.
Ref.: [4]
PassFailN/A - 7.
The blade, disc or wheel fitted is free of cracks and visible damageCritical
Inspect an abrasive wheel closely before you mount it.
PassFailN/A - 8.
On a grinder, the maximum speed marked on the wheel is not lower than the speed of the toolCritical
Compare the rpm on the wheel with the rpm on the tool's rating plate. Mark N/A for other tools.
PassFailN/A - 9.PassFailN/A
Cable, plug and supply (corded tools)
- 10.
The supply cable is free of cuts, fraying and other damage along its whole lengthCritical
PassFailN/A - 11.
The cable has no taped joints or improvised repairsCritical
Ref.: [8]
PassFailN/A - 12.
The outer sheath is held firmly where the cable enters the plug and the tool; no coloured inner cores are showingCritical
Ref.: [8]
PassFailN/A - 13.
The plug is not cracked, its pins are straight and none has been removed or alteredCritical
PassFailN/A - 14.
The tool is either marked as double insulated or has an earthed (three-conductor) cable and plugCritical
Look for the double-insulation mark on the rating plate. If you cannot see it, treat the tool as one that needs an earth.
PassFailN/A - 15.
Any extension lead, with its plug and socket, is undamaged and suited to the toolCritical
PassFailN/A - 16.
On a temporary or construction supply, the socket used is protected by a residual current device (RCD/GFCI)
This is the US rule (OSHA 1910.304(b)(3)); elsewhere, follow the site's electrical rules.
PassFailN/A
Battery and charger (battery tools)
Air hose and connections (pneumatic tools)
- 20.
The air hose is free of cuts, cracks and worn patchesCritical
Ref.: [2]
PassFailN/A - 21.
The tool is secured to the hose by a positive means, using the couplings or clamps the manufacturer specifiesCritical
PassFailN/A - 22.
On impact tools, the safety clip or retainer that holds the chisel or bit is fitted and secureCritical
PassFailN/A - 23.
The supply pressure is set to suit the tool and does not exceed the rating of the hose and fittingsCritical
PassFailN/A - 24.
A hose with an inside diameter over 1/2 inch (12.7 mm) has a safety device at the supply or branch line
The device reduces the pressure if the hose fails. This is the US rule (OSHA 1926.302(b)(7)).
PassFailN/A - 25.
A nailer or stapler has a working safety device on the muzzle, so it fires only when pressed against the workCritical
Mark N/A for other tools.
Ref.: [5]
PassFailN/A
Function test (connected, no load)
- 26.
The switch works, and the tool stops when the trigger is released or the switch is turned offCritical
A lock-on button must release with one movement of the same finger.
PassFailN/A - 27.
On a short run without load, the tool starts, runs and stops normallyCritical
Stand out of the line of a wheel or blade while it comes up to speed.
PassFailN/A
Result
Critical check: if it fails, stop and correct it before work continues.
Sign-off
Tool user
Supervisor
Run this checklist on your phone
FindRisk turns inspections into a few taps: AI-generated checklists you can edit and save as templates, photo markup with AI hazard analysis, Fine-Kinney risk scoring and an instant PDF report.
Download FindRiskLegal basis and references
- [1] Türkiye: İş Ekipmanlarının Kullanımında Sağlık ve Güvenlik Şartları Yönetmeliği (Resmî Gazete, 25.04.2013) — Article 5 (suitable equipment); Annex I 2.3 and 2.8 (stopping, guards); Annex III 1.3 to 1.3.2: operator checks before each start of work, visual check and function test, defective equipment taken out of use.
- [2] Türkiye: T.C. Çalışma ve Sosyal Güvenlik Bakanlığı, İSGGM, Güvenli İnşaat Bilgi Kartı: El Aletleri, Kontrol Tedbirleri — Control measures for electric, battery and pneumatic hand tools (guidance). Card 1 of the same series describes the hazards.
- [3] United States: OSHA 29 CFR 1910.334, Use of equipment — (a)(2) visual inspection of portable cord- and plug-connected equipment before use on any shift and removal of defective items from service; (a)(3) grounding-type equipment.
- [4] United States: OSHA 29 CFR 1910.243, Guarding of portable powered tools — (a)(1) circular saw guards; (a)(2) switches and controls; (a)(4) cracked saws; (b)(1) tool retainers; (c) abrasive wheel guards, inspection before mounting and spindle speed.
- [5] United States: OSHA 29 CFR 1926.302, Power-operated hand tools (with 1926.300, General requirements) — 1926.302(a)(1) double-insulated or grounded electric tools; (b)(1) to (b)(7) pneumatic tools and hoses. 1926.300(b)(1) guards fitted when in use; 1926.300(d) switches.
- [6] United States: OSHA 29 CFR 1910.304, Wiring design and protection — (b)(3)(ii) ground-fault circuit-interrupter protection on temporary wiring; (g)(6)(vi) and (vii) grounding of hand-held motor-operated tools and the double-insulation exemption.
- [7] United States: OSHA 3080, Hand and Power Tools (2002, revised) — OSHA's summary booklet: examine each tool before use, tag damaged electric tools "Do Not Use", abrasive wheel and pneumatic tool precautions.
- [8] United Kingdom: HSE, Maintaining portable electrical equipment, HSG107 (Third edition, 2013) — Paragraphs 38 and 39: user checks and what to do when a fault is found; Table 1: suggested initial intervals (not legal requirements).
- [9] United Kingdom: HSE, Safety in the use of abrasive wheels, HSG17 (Third edition, 2000) — Paragraph 15 (use-by date of organic bonded wheels for hand-held use); 18 (examination and ring test); 28 (maximum operating speed marking); 68 (guards on portable machines).
Version 1 · Updated November 20, 2026 · findrisk.net/checklists/portable-power-tool-inspection-checklist/
Fill in this checklist on your phone. Scan to download FindRisk: run the checklist, add photos, score risks and share a PDF report in minutes.
Version 1 · Updated November 20, 2026 · findrisk.net/checklists/portable-power-tool-inspection-checklist/
Frequently asked questions
How often should power tools be inspected?
Before use. OSHA 29 CFR 1910.334(a)(2) requires portable cord- and plug-connected equipment to be visually inspected before use on any shift, and Türkiye's Work Equipment Regulation (Annex III, 1.3) requires an operator check before each start of work. HSE's HSG107 suggests user checks daily or every shift for 230 V tools on construction sites and weekly for 110 V tools, and says these suggested intervals are not legal requirements.
What should you do with a damaged power tool?
Stop using it and take it out of service. OSHA 1910.334(a)(2)(ii) says a defective or damaged item is removed from service until the repairs and tests needed to make it safe have been done, and OSHA's Hand and Power Tools booklet tells employers to tag damaged portable electric tools "Do Not Use". HSG107 adds that faults are reported to the manager and the tool is repaired by a competent person before it is used again.
Is PAT testing of power tools a legal requirement in the UK?
Not as such. HSG107 explains that the Electricity at Work Regulations require equipment to be maintained to prevent danger, but do not specify what needs to be done, by whom or how frequently. HSE recommends a mix of user checks, formal visual inspections and, where necessary, combined inspection and testing at intervals set by the dutyholder's risk assessment.
Do battery power tools need a pre-use check?
Yes, for everything except the mains cable. HSG107 lists battery-operated equipment below 40 V as needing no electrical inspection or test, but the charger is mains equipment and gets user checks. Guards, blades, discs and switches carry the same risks whatever the power source, and the Turkish Ministry of Labour's hand tools card says to use only the batteries and chargers the manufacturer specifies.
What should be checked on an angle grinder before use?
The guard, the wheel and the speed. OSHA 1910.243(c) requires abrasive wheels to be used with a safety guard that leaves no more than 180 degrees of the wheel exposed, the wheel to be closely inspected before mounting, and the spindle speed to be checked against the maximum speed marked on the wheel. HSE's HSG17 adds that organic bonded wheels for hand-held machines carry a use-by date of three years from manufacture.
