FindRisk Logo
All checklists

Equipment

Harness Inspection Checklist: Full Body Harness and Lanyard

Frequency
Before each use
Completed by
Harness user or competent person
Approved by
Supervisor
The checklist
36 checks · 6 sections

A harness inspection checklist is the check a worker makes on a full body harness, lanyard and connectors before putting them on, and the record a competent person uses for the periodic detailed inspection. It covers the label and inspection status, webbing and stitching, metal parts, the lanyard and energy absorber, and the fit and connection before work starts. A harness that fails a critical check is taken out of service.

In the United States, OSHA 29 CFR 1910.140(c)(18) requires personal fall protection systems to be inspected before initial use during each workshift, and 1926.502(d)(21) requires construction fall arrest systems to be inspected before each use. In the UK, HSE guidance INDG367 recommends a tactile and visual pre-use check every time, plus a recorded detailed inspection at least every six months. In Türkiye, the PPE Use Regulation requires PPE to be checked before every use and to be maintained and periodically inspected according to the manufacturer's instructions.

This form does not replace the manufacturer's instructions or the detailed inspection by a competent person, and a harness only protects as part of a system with a suitable anchor and a rescue plan. For the full pre-task check and inspection intervals, see our working at height checklist; for choosing the right equipment, see the PPE hazard assessment guide.

How to use this checklist

  1. Check the harness yourself before each use, and hand it to a competent person for the detailed inspection at the interval in your inspection regime.
  2. Do the condition checks in good light before putting the harness on: pass every strap slowly through your hands, then check the metal parts and the lanyard.
  3. Put the harness on and complete the fit and connection checks before you go to the work position.
  4. Mark each check Pass, Fail or N/A and photograph any defect.
  5. If a critical check fails, do not use the harness: label it "Do not use", take it out of service and hand it to your supervisor or the competent person.
  6. Keep the completed form with the harness's inspection record.

The checklist: Harness Inspection Checklist: Full Body Harness and Lanyard

Inspection details

Site / area: 
Harness ID / serial number: 
Manufacturer and model: 
Date of manufacture: 
Last detailed inspection: 
Lanyard ID (if checked with the harness): 
Inspection type: 
Date and time: 

Label and records

  1. 1.

    The harness label is present and legible, showing the manufacturer, model, serial or batch number and date of manufactureCritical

    A harness without a readable label cannot be matched to its inspection record: withdraw it.

    Ref.: [5] [2] [6]

    PassFailN/A
  2. 2.

    The harness carries the CE marking with the four-digit notified body number

    Applies in the EU and Türkiye, where fall protection PPE is Category III; instructions for use in the local language must also be available. Mark N/A elsewhere.

    Ref.: [1] [2]

    PassFailN/A
  3. 3.

    A detailed inspection by a competent person is recorded and still within the interval set in the inspection regimeCritical

    HSE recommends at least every 6 months, and at least every 3 months for frequent use in arduous work; follow the manufacturer if stricter. Withdraw a harness with no record of inspection in the last 6 months.

    Ref.: [5] [1] [2]

    PassFailN/A
  4. 4.

    The harness is within the service life set by the manufacturer or your company

    Compare the date of manufacture on the label with the service-life policy.

    Ref.: [1] [6]

    PassFailN/A
  5. 5.

    The harness has not arrested a fall, and any fall indicator is intactCritical

    Equipment that has arrested a fall stays out of service until a competent person has inspected it and found it safe.

    Ref.: [3] [4] [5] [2] [6]

    PassFailN/A
  6. 6.

    There are no user modifications: no extra holes, knots or repairs not approved by the manufacturerCritical

    Ref.: [5] [1] [6]

    PassFailN/A

Webbing and stitching

Pass every strap slowly through your hands in good light. Bend it into an inverted U to open up cuts, and check both sides along its full length.

  1. 7.

    Webbing has no cuts, nicks or tears, including small cuts at the edgesCritical

    HSE notes that a 1 mm cut at the edge can reduce strength by 5 to 40% depending on the make.

    Ref.: [5] [2] [3]

    PassFailN/A
  2. 8.

    Webbing has no fraying, broken fibres or abrasion on its face, edges or loopsCritical

    Ref.: [5] [2] [6]

    PassFailN/A
  3. 9.

    There are no burns, melted, glazed or hardened areas from heat or frictionCritical

    Heat-damaged fibres look glazed and feel harder than the webbing around them.

    Ref.: [5] [2] [6]

    PassFailN/A
  4. 10.

    There is no chemical damage: no soft, flaking or discoloured areasCritical

    Ref.: [5] [2]

    PassFailN/A
  5. 11.

    There are no signs of UV damage, such as faded colour or a powdery surfaceCritical

    UV damage is hard to see. If in doubt, withdraw the harness for a detailed inspection.

    Ref.: [5] [2]

    PassFailN/A
  6. 12.

    Webbing is free of mildew, paint, dirt, grit and sand

    Grit works into the fibres and wears them from inside. Clean as the manufacturer instructs; withdraw heavily contaminated webbing for review.

    Ref.: [5] [3] [6]

    PassFailN/A
  7. 13.

    Load-bearing stitching is intact, with no pulled, cut, broken or missing stitchesCritical

    Check the stitch patterns around the D-rings and where the leg, chest and back straps join.

    Ref.: [5] [2] [6]

    PassFailN/A

Metal parts

  1. 14.

    D-rings have no bends, cracks, breaks or sharp or rough edgesCritical

    Ref.: [2] [3] [6]

    PassFailN/A
  2. 15.

    The back D-ring pivots freely and its back pad is undamaged

    Ref.: [2]

    PassFailN/A
  3. 16.

    Buckles and adjusters are not bent, distorted, cracked or unusually wornCritical

    Ref.: [2] [6]

    PassFailN/A
  4. 17.

    Every buckle fastens, locks and holds its strap without slippingCritical

    On tongue buckles, the tongue overlaps the frame and moves freely, and the strap holes (grommets) are undamaged.

    Ref.: [2] [6]

    PassFailN/A
  5. 18.

    Metal parts are free of rust and corrosionCritical

    Ref.: [2] [3] [6]

    PassFailN/A

Lanyard, energy absorber and connectors

Check the lanyard you will use with this harness. Mark N/A if it is inspected on its own form.

  1. 19.

    The lanyard webbing or rope has no cuts, abrasion, damaged stitching or knotsCritical

    Pass the whole lanyard through your hands, as for the harness. Its label must also be legible.

    Ref.: [5] [3] [2]

    PassFailN/A
  2. 20.

    The energy absorber cover is intact and the absorber has not started to deployCritical

    Look for tear webbing pulled out of the pack, or a damaged or displaced cover.

    Ref.: [5] [2]

    PassFailN/A
  3. 21.

    Snaphooks and karabiners are not bent, cracked, deformed or corrodedCritical

    Ref.: [5] [3]

    PassFailN/A
  4. 22.

    Connector gates close and lock by themselves and need two separate actions to openCritical

    Ref.: [3] [4] [5]

    PassFailN/A
  5. 23.

    The lanyard and connectors are compatible with the harness attachment point and the anchorCritical

    A snaphook must be sized for the part it connects to.

    Ref.: [3] [4]

    PassFailN/A

Fit and connection (before work)

Mark N/A during a detailed inspection away from the work position.

  1. 24.

    A full body harness is used for fall arrest, not a body beltCritical

    Ref.: [3] [2]

    PassFailN/A
  2. 25.

    The harness is the right size and adjusted to fit the wearer snugly

    Ref.: [1] [2]

    PassFailN/A
  3. 26.

    Both leg straps are fastened and tightenedCritical

    Ref.: [2]

    PassFailN/A
  4. 27.

    The chest strap is fastened across the middle of the chest

    Ref.: [2]

    PassFailN/A
  5. 28.

    The back D-ring sits between the shoulder blades, near shoulder level

    Ref.: [3] [4] [2]

    PassFailN/A
  6. 29.

    Loose strap ends are tucked in and not left hanging

    Ref.: [2]

    PassFailN/A
  7. 30.

    The lanyard is connected to an anchor suitable for fall arrest, not to a guardrail or scaffold memberCritical

    OSHA: 5,000 lb (22.2 kN) per person attached, or designed by a qualified person with a safety factor of at least two.

    Ref.: [3] [2]

    PassFailN/A
  8. 31.

    There is enough clear distance below the worker for the lanyard, energy absorber and harness stretchCritical

    ÇSGB guide: with a lanyard and energy absorber, allow 2 × lanyard length (including the absorber) + 1.75 m + 1 m safety margin, plus harness stretch. OSHA limits free fall to 6 ft (1.8 m).

    Ref.: [2] [3]

    PassFailN/A
  9. 32.

    A rescue plan is in place to reach a worker suspended in the harness promptlyCritical

    The ÇSGB guide also asks that a worker using fall arrest is watched or accompanied by another worker.

    Ref.: [3] [4] [2]

    PassFailN/A

Result

  1. 33.

    If a critical check failed, the harness is labelled "Do not use", taken out of service and passed to a competent personCritical

    Ref.: [5] [3] [1]

    YesNoN/A
  2. 34.

    Every defect found has been reported to the supervisor

    Ref.: [1] [6]

    YesNoN/A
  3. 35.

    The result is entered in the harness's inspection record

    Ref.: [5] [2]

    YesNoN/A
  4. 36.

    Notes and defects found

    Note: ________

Critical check: if it fails, stop and correct it before work continues.

Sign-off

Inspected by (user or competent person)

Name: 
Signature: 
Date: 

Supervisor

Name: 
Signature: 
Date: 

Run this checklist on your phone

FindRisk turns inspections into a few taps: AI-generated checklists you can edit and save as templates, photo markup with AI hazard analysis, Fine-Kinney risk scoring and an instant PDF report.

Download FindRisk

Legal basis and references

  1. [1] Türkiye: Kişisel Koruyucu Donanımların İşyerlerinde Kullanılması Hakkında Yönetmelik (Resmî Gazete, 02.07.2013, 28695) — Art. 6(1)(a) fit, CE marking and Turkish instructions; 6(1)(c) period of use; 6(1)(e) maintenance and periodic checks per the manufacturer's instructions; 7(2)(b) modifications; 8(3) report defects, check before every use.
  2. [2] Türkiye: ÇSGB, Yapı İşlerinde Yüksekte Çalışmalarda İş Sağlığı ve Güvenliği Uygulama Rehberi (2018) — 3.3.4 personal fall arrest systems (pre-use check, anchors, after a fall, clearance); Annex 1: harness inspection (webbing, D-rings, buckles, labels), donning, lanyards and energy absorbers.
  3. [3] United States: OSHA 29 CFR 1910.140, Personal fall protection systems — (c)(1)–(2) connectors; (c)(9) locking connectors; (c)(13) anchorages; (c)(17) impact loading; (c)(18) inspection before initial use each workshift; (c)(19) compatibility; (c)(21) rescue; (c)(22) attachment point; (d)(2)(ii) free fall; (d)(3) body belts prohibited.
  4. [4] United States: OSHA 29 CFR 1926.502, Fall protection systems criteria and practices — (d)(5) locking snaphooks sized for the connection; (d)(17) attachment point; (d)(19) impact loading; (d)(20) rescue; (d)(21) inspection before each use.
  5. [5] United Kingdom: HSE INDG367, Inspecting fall arrest equipment made from webbing or rope — Pre-use checks, detailed and interim inspections, examples of defects, withdrawal from use; cites the BS EN 365 twelve-monthly examination.
  6. [6] United States: Miller (Protective Industrial Products), Harness End-User Pre-Use Inspection Guide + Daily Checklist (2026) — Manufacturer guidance: label and service life, fall indicator, webbing, stitching and hardware stop-use criteria.

Version 1 · Updated October 29, 2026 · findrisk.net/checklists/full-body-harness-inspection-checklist/

Frequently asked questions

How often should a full body harness be inspected?

Before every use, by the person wearing it. OSHA 1910.140(c)(18) requires an inspection before initial use during each workshift. HSE guidance INDG367 adds a recorded detailed inspection by a competent person at least every six months, or at least every three months for frequent use in arduous work such as scaffolding. Follow the manufacturer's instructions if they ask for more.

Who is allowed to inspect a safety harness?

The user does the pre-use check by touch and by eye. Detailed inspections are done by a competent person: OSHA describes one as someone able to identify hazards and authorised to take prompt corrective action, and HSE says the inspector should be impartial and have the authority to discard defective equipment.

Can a harness be used again after a fall?

Not until a competent person has inspected it. OSHA 1910.140(c)(17) requires equipment that has been impact-loaded to be removed from service immediately and not used again until a competent person finds it undamaged and safe. HSE is stricter for lanyards: one that has arrested a fall should never be reused.

Which defects mean a harness must be taken out of service?

Cuts, fraying, broken fibres, burns, chemical or UV damage to the webbing; pulled or broken stitching; bent, cracked or corroded D-rings and buckles; a missing or unreadable label; and an energy absorber that has started to deploy. HSE notes that a 1 mm cut at the edge of webbing can reduce its strength by 5 to 40% depending on the make.

Where should the D-ring be on a full body harness?

In the centre of the back, between the shoulder blades and near shoulder level. OSHA 1910.140(c)(22) requires this position for fall arrest and allows a front (sternal) attachment only where free fall is limited to 2 feet (0.6 m).