Customize & download
Harness Inspection Checklist: Full Body Harness and Lanyard
Adapt this checklist to your site: edit, add, remove and reorder the checks, add your company name and logo, then save it as a PDF. Nothing is uploaded; your changes stay in this browser.
Your form
Inspection details (blank fields on the form)8 fields
The checklist · 36 checks · 6 sections
Sign-off (who signs the form)2 signers
FindRiskfindrisk.netHarness Inspection Checklist: Full Body Harness and Lanyard
Inspection details
Label and records
- 1.
The harness label is present and legible, showing the manufacturer, model, serial or batch number and date of manufactureCritical
A harness without a readable label cannot be matched to its inspection record: withdraw it.
Ref.: [5] [2] [6]
PassFailN/A - 2.
The harness carries the CE marking with the four-digit notified body number
Applies in the EU and Türkiye, where fall protection PPE is Category III; instructions for use in the local language must also be available. Mark N/A elsewhere.
Ref.: [1] [2]
PassFailN/A - 3.
A detailed inspection by a competent person is recorded and still within the interval set in the inspection regimeCritical
HSE recommends at least every 6 months, and at least every 3 months for frequent use in arduous work; follow the manufacturer if stricter. Withdraw a harness with no record of inspection in the last 6 months.
Ref.: [5] [1] [2]
PassFailN/A - 4.
The harness is within the service life set by the manufacturer or your company
Compare the date of manufacture on the label with the service-life policy.
Ref.: [1] [6]
PassFailN/A - 5.
The harness has not arrested a fall, and any fall indicator is intactCritical
Equipment that has arrested a fall stays out of service until a competent person has inspected it and found it safe.
Ref.: [3] [4] [5] [2] [6]
PassFailN/A - 6.
There are no user modifications: no extra holes, knots or repairs not approved by the manufacturerCritical
Ref.: [5] [1] [6]
PassFailN/A
Webbing and stitching
Pass every strap slowly through your hands in good light. Bend it into an inverted U to open up cuts, and check both sides along its full length.
- 7.
Webbing has no cuts, nicks or tears, including small cuts at the edgesCritical
HSE notes that a 1 mm cut at the edge can reduce strength by 5 to 40% depending on the make.
Ref.: [5] [2] [3]
PassFailN/A - 8.
Webbing has no fraying, broken fibres or abrasion on its face, edges or loopsCritical
Ref.: [5] [2] [6]
PassFailN/A - 9.
There are no burns, melted, glazed or hardened areas from heat or frictionCritical
Heat-damaged fibres look glazed and feel harder than the webbing around them.
Ref.: [5] [2] [6]
PassFailN/A - 10.
There is no chemical damage: no soft, flaking or discoloured areasCritical
Ref.: [5] [2]
PassFailN/A - 11.
There are no signs of UV damage, such as faded colour or a powdery surfaceCritical
UV damage is hard to see. If in doubt, withdraw the harness for a detailed inspection.
Ref.: [5] [2]
PassFailN/A - 12.
Webbing is free of mildew, paint, dirt, grit and sand
Grit works into the fibres and wears them from inside. Clean as the manufacturer instructs; withdraw heavily contaminated webbing for review.
Ref.: [5] [3] [6]
PassFailN/A - 13.
Load-bearing stitching is intact, with no pulled, cut, broken or missing stitchesCritical
Check the stitch patterns around the D-rings and where the leg, chest and back straps join.
Ref.: [5] [2] [6]
PassFailN/A
Metal parts
- 14.
D-rings have no bends, cracks, breaks or sharp or rough edgesCritical
Ref.: [2] [3] [6]
PassFailN/A - 15.
The back D-ring pivots freely and its back pad is undamaged
Ref.: [2]
PassFailN/A - 16.
Buckles and adjusters are not bent, distorted, cracked or unusually wornCritical
Ref.: [2] [6]
PassFailN/A - 17.
Every buckle fastens, locks and holds its strap without slippingCritical
On tongue buckles, the tongue overlaps the frame and moves freely, and the strap holes (grommets) are undamaged.
Ref.: [2] [6]
PassFailN/A - 18.
Metal parts are free of rust and corrosionCritical
Ref.: [2] [3] [6]
PassFailN/A
Lanyard, energy absorber and connectors
Check the lanyard you will use with this harness. Mark N/A if it is inspected on its own form.
- 19.
The lanyard webbing or rope has no cuts, abrasion, damaged stitching or knotsCritical
Pass the whole lanyard through your hands, as for the harness. Its label must also be legible.
Ref.: [5] [3] [2]
PassFailN/A - 20.
The energy absorber cover is intact and the absorber has not started to deployCritical
Look for tear webbing pulled out of the pack, or a damaged or displaced cover.
Ref.: [5] [2]
PassFailN/A - 21.
Snaphooks and karabiners are not bent, cracked, deformed or corrodedCritical
Ref.: [5] [3]
PassFailN/A - 22.
Connector gates close and lock by themselves and need two separate actions to openCritical
Ref.: [3] [4] [5]
PassFailN/A - 23.
The lanyard and connectors are compatible with the harness attachment point and the anchorCritical
A snaphook must be sized for the part it connects to.
Ref.: [3] [4]
PassFailN/A
Fit and connection (before work)
Mark N/A during a detailed inspection away from the work position.
- 24.
A full body harness is used for fall arrest, not a body beltCritical
Ref.: [3] [2]
PassFailN/A - 25.
The harness is the right size and adjusted to fit the wearer snugly
Ref.: [1] [2]
PassFailN/A - 26.
Both leg straps are fastened and tightenedCritical
Ref.: [2]
PassFailN/A - 27.
The chest strap is fastened across the middle of the chest
Ref.: [2]
PassFailN/A - 28.
The back D-ring sits between the shoulder blades, near shoulder level
Ref.: [3] [4] [2]
PassFailN/A - 29.
Loose strap ends are tucked in and not left hanging
Ref.: [2]
PassFailN/A - 30.
The lanyard is connected to an anchor suitable for fall arrest, not to a guardrail or scaffold memberCritical
OSHA: 5,000 lb (22.2 kN) per person attached, or designed by a qualified person with a safety factor of at least two.
Ref.: [3] [2]
PassFailN/A - 31.
There is enough clear distance below the worker for the lanyard, energy absorber and harness stretchCritical
ÇSGB guide: with a lanyard and energy absorber, allow 2 × lanyard length (including the absorber) + 1.75 m + 1 m safety margin, plus harness stretch. OSHA limits free fall to 6 ft (1.8 m).
Ref.: [2] [3]
PassFailN/A - 32.
A rescue plan is in place to reach a worker suspended in the harness promptlyCritical
The ÇSGB guide also asks that a worker using fall arrest is watched or accompanied by another worker.
Ref.: [3] [4] [2]
PassFailN/A
Result
- 33.
If a critical check failed, the harness is labelled "Do not use", taken out of service and passed to a competent personCritical
Ref.: [5] [3] [1]
YesNoN/A - 34.
Every defect found has been reported to the supervisor
Ref.: [1] [6]
YesNoN/A - 35.
The result is entered in the harness's inspection record
Ref.: [5] [2]
YesNoN/A - 36.
Notes and defects found
Note: ________
Critical check: if it fails, stop and correct it before work continues.
Sign-off
Inspected by (user or competent person)
Supervisor
Legal basis and references
- [1] Türkiye: Kişisel Koruyucu Donanımların İşyerlerinde Kullanılması Hakkında Yönetmelik (Resmî Gazete, 02.07.2013, 28695) — Art. 6(1)(a) fit, CE marking and Turkish instructions; 6(1)(c) period of use; 6(1)(e) maintenance and periodic checks per the manufacturer's instructions; 7(2)(b) modifications; 8(3) report defects, check before every use.
- [2] Türkiye: ÇSGB, Yapı İşlerinde Yüksekte Çalışmalarda İş Sağlığı ve Güvenliği Uygulama Rehberi (2018) — 3.3.4 personal fall arrest systems (pre-use check, anchors, after a fall, clearance); Annex 1: harness inspection (webbing, D-rings, buckles, labels), donning, lanyards and energy absorbers.
- [3] United States: OSHA 29 CFR 1910.140, Personal fall protection systems — (c)(1)–(2) connectors; (c)(9) locking connectors; (c)(13) anchorages; (c)(17) impact loading; (c)(18) inspection before initial use each workshift; (c)(19) compatibility; (c)(21) rescue; (c)(22) attachment point; (d)(2)(ii) free fall; (d)(3) body belts prohibited.
- [4] United States: OSHA 29 CFR 1926.502, Fall protection systems criteria and practices — (d)(5) locking snaphooks sized for the connection; (d)(17) attachment point; (d)(19) impact loading; (d)(20) rescue; (d)(21) inspection before each use.
- [5] United Kingdom: HSE INDG367, Inspecting fall arrest equipment made from webbing or rope — Pre-use checks, detailed and interim inspections, examples of defects, withdrawal from use; cites the BS EN 365 twelve-monthly examination.
- [6] United States: Miller (Protective Industrial Products), Harness End-User Pre-Use Inspection Guide + Daily Checklist (2026) — Manufacturer guidance: label and service life, fall indicator, webbing, stitching and hardware stop-use criteria.
Fill in this checklist on your phone. Scan to download FindRisk: run the checklist, add photos, score risks and share a PDF report in minutes.
This form was customized by its user from a FindRisk template. It is a guide and does not replace a risk assessment or the periodic inspection by a competent person.
Based on the template at: findrisk.net/checklists/full-body-harness-inspection-checklist/ · Version 1