Customize & download
Racking Inspection Checklist: Weekly Pallet Racking Checks
Adapt this checklist to your site: edit, add, remove and reorder the checks, add your company name and logo, then save it as a PDF. Nothing is uploaded; your changes stay in this browser.
Your form
Inspection details (blank fields on the form)6 fields
The checklist · 32 checks · 5 sections
Sign-off (who signs the form)2 signers
FindRiskfindrisk.netRacking Inspection Checklist: Weekly Pallet Racking Checks
Inspection details
Load notices and records
- 1.
Each run has a clear load notice securely fixed to it, showing the maximum load and any required load configuration
A typical notice gives the maximum load per beam level and per bay, the height to the first beam and the beam pitch.
Ref.: [1] [3]
PassFailN/A - 2.
Beam levels and other adjustable parts match the configuration on the load noticeCritical
Moving the first or second beam from the bottom is the most critical change and always needs a capacity check and an updated notice.
Ref.: [1] [3]
PassFailN/A - 3.
The last expert inspection was within 12 months and its proposed actions are closed or in progress
Ref.: [1] [3]
PassFailN/A - 4.
Inspections, damage and repairs are recorded in a log, and earlier amber items have been repaired within four weeks
Under HSG76, amber damage not repaired within four weeks of its designation becomes red.
Ref.: [1] [2] [3]
PassFailN/A
Structure (from ground level)
Judge damage against the manufacturer's or the expert inspector's limits. Any damage reduces the racking's load capacity.
- 5.
Uprights are free of dents, bends, twists, splits or other impact damageCritical
Look hardest at the lower levels and at corner uprights next to aisles and gangways.
Ref.: [1] [3]
PassFailN/A - 6.
Uprights stand vertical and the racking does not leanCritical
Ref.: [3]
PassFailN/A - 7.
Horizontal and diagonal frame bracing is in place, straight and attached at both endsCritical
Ref.: [1] [3]
PassFailN/A - 8.
Beams are not bent, dented or visibly saggingCritical
Ref.: [1] [3]
PassFailN/A - 9.
Beam-to-upright connectors and welds show no cracks or deformationCritical
Ref.: [3] [1]
PassFailN/A - 10.
A beam connector lock is fitted and engaged at each end of every beamCritical
Locks stop a beam lifting out if a lift truck catches it from below.
Ref.: [1] [3]
PassFailN/A - 11.
Base plates are in place and undamaged, and floor fixings are present and secureCritical
Free-standing racks should not be used where lift trucks or other handling equipment work.
Ref.: [1] [3]
PassFailN/A - 12.
The floor under the racking is sound and level, with no cracking or settlement at the base plates
Ref.: [1] [3]
PassFailN/A - 13.
Run spacers on back-to-back runs and any wall ties are in place and undamaged
Ref.: [1]
PassFailN/A - 14.
The racking has not been altered (no welding, cutting or drilling) and no components have been removedCritical
Any change needs the manufacturer's advice first.
Ref.: [1] [3]
PassFailN/A
Protection, aisles and access
- 15.
Column guards are fitted where uprights are likely to be struck, and are undamaged
A damaged guard is replaced; also check the upright behind it.
Ref.: [1] [3]
PassFailN/A - 16.
Corner uprights at the ends of runs have a protective device in a conspicuous colour
Ref.: [1] [3]
PassFailN/A - 17.
Aisles are clear, tidy and wide enough for the handling equipment to manoeuvre
No stock, pallets or waste left in aisles. OSHA also requires permanent aisles to be marked.
Ref.: [3] [1] [5]
PassFailN/A - 18.
No one climbs the racking, and upper levels are reached only with suitable access equipmentCritical
Ref.: [1] [2] [3]
PassFailN/A - 19.
Safety signs on the racking (for example do not climb, report all damage) are present and legible
Ref.: [3] [1]
PassFailN/A - 20.
Top loads keep the clearance below sprinklers required by the fire protection design
US: OSHA 1910.159(c)(10) requires at least 18 in (45.7 cm) between sprinklers and the material below.
Ref.: [6]
PassFailN/A
Loads and pallets
- 21.
No beam level or bay is loaded above the limits on the load noticeCritical
The weight of each pallet load should be known before it is stored, especially for new or mixed product lines.
Ref.: [1] [3]
PassFailN/A - 22.
Pallets sit squarely on both beams and loads are spread evenly along each beam
Ref.: [3] [1]
PassFailN/A - 23.
Clearances are kept between adjacent loads, between loads and uprights, and between the top of each load and the beam above
ÇSGB Table 4.3 (beam height up to 3000 mm): 75 mm each; up to 6000 mm: 75, 75 and 100 mm above the load. Back-to-back loads: at least 100 mm (Table 4.2).
Ref.: [3]
PassFailN/A - 24.
Loads are stable and secured on their pallets, and nothing overhangs into the aisle or is pushed through to the backCritical
Ref.: [3] [1] [2] [5]
PassFailN/A - 25.
Pallets in the racking are in good condition, with no broken boards or bearers
Ref.: [1] [2] [3]
PassFailN/A - 26.
Pallets suit this racking system, and no one-trip (expendable) pallets are stored in it
Ref.: [1] [2] [3]
PassFailN/A - 27.
Pallets are lowered onto the beams and are not slid or pushed along them
Ref.: [1] [3]
PassFailN/A
Damage action and result
- 28.
Every damaged component found has been graded green, amber or red
Green: record and re-examine at later inspections. Amber: repair as soon as possible. Red: immediate action.
Ref.: [1]
YesNoN/A - 29.
Any red-risk area has been offloaded at once and isolated so it cannot be used until repairedCritical
For example, offload the bay in the inspector's presence and rope it off. Repair is usually by replacing the damaged component.
Ref.: [1] [2]
YesNoN/A - 30.
Amber-risk locations are labelled with the date and are not reloaded once emptied until repairedCritical
Ref.: [1]
YesNoN/A - 31.
Every defect has been reported in writing to the person responsible for racking safety and entered in the log
Ref.: [1] [3] [4]
YesNoN/A - 32.
Notes, defect locations and grades
Note: ________
Critical check: if it fails, stop and correct it before work continues.
Sign-off
Inspected by
Person responsible for racking safety
Legal basis and references
- [1] United Kingdom: HSE HSG76: Warehousing and storage – A guide to health and safety (Second edition, 2007) — Para 596 and 655: no climbing on racking; 611, 617: pallet suitability and inspection, expendable pallets; 619: pallets lowered onto beams; 633–634: installation, floor, run spacers, floor fixing, beam connector locks, load notice (Figure 48), no alterations, capacity check when moving beams; 636–638: free-standing racks and floor fixing; 639: column guards and corner uprights; 641–652: damage reduces capacity, PRRS, immediate reporting, weekly or regular visual inspections with a record, expert inspection at intervals of not more than 12 months, log; Table 11: green, amber and red damage and actions.
- [2] United Kingdom: HSE INDG412: Warehousing and storage – Keep it safe — Pallets inspected before each use and suited to the racking; racking protected where it may be struck; three types of inspection (immediate reporting, regular visual, expert); offload damaged racking and prevent use until remedied; logbook; no climbing.
- [3] Türkiye: ÇSGB İş Sağlığı ve Güvenliği Genel Müdürlüğü, Güvenli İstifleme Rehberi (Revizyon 2024) — Advisory guide. p. 50–51: pallet checks, one-trip pallets; 4.4 (p. 54): load and design marking; 4.4.1.1 (p. 55–56): installation by authorised persons, floor, floor fixing, aisles, beam locks, load plate, no alterations; 4.4.1.2 (p. 57): no climbing, clearances, tidy aisles, damage and repair records; 4.4.1.3 (p. 57–58): immediate reporting, weekly and monthly in-house checks, yearly expert check under TS EN 15635 and the points to check; 4.4.2 (p. 58–59): load sign, upright protectors, even loading, no sliding along beams; 4.4.3 (p. 59–61): clearances, Tables 4.2 and 4.3.
- [4] Türkiye: 6331 sayılı İş Sağlığı ve Güvenliği Kanunu (Resmî Gazete, 30.06.2012) — Art. 4(1): the employer takes every measure to prevent occupational risks, monitors and checks that the measures are followed, and carries out a risk assessment.
- [5] United States: OSHA 29 CFR 1910.176, Handling materials – general — (a): safe clearances for aisles where mechanical handling equipment is used, aisles kept clear and in good repair, permanent aisles marked; (b): storage shall not create a hazard, stored material stable and secure against sliding or collapse; (c): storage areas free from accumulations that create tripping, fire or explosion hazards.
- [6] United States: OSHA 29 CFR 1910.159, Automatic sprinkler systems — (c)(10): minimum vertical clearance of 18 inches (45.7 cm) between sprinklers and the material below.
Fill in this checklist on your phone. Scan to download FindRisk: run the checklist, add photos, score risks and share a PDF report in minutes.
This form was customized by its user from a FindRisk template. It is a guide and does not replace a risk assessment or the periodic inspection by a competent person.
Based on the template at: findrisk.net/checklists/pallet-racking-inspection-checklist/ · Version 1